![]() ![]() ![]() Which of the options 11-14 best suits your needs is explained in the WinGDB helpfile.ġ5 comments to Howto Plan Routes and Tracks Whereas routes only offer 50 viapoints (on most outdoor units, Some GPS may have higher limits), tracks can have 500 or more points per track depending on the GPS you want to use the track with. Tracks are overlayed on you GPS over the map (whereas routes are shown below a street), and guide you in straight lines between each point. If you don't have the Openmtbmap installed on your GPS, you can still profit from routes calculated with Mapsource, by using WinGDB to convert Routes into Tracks.Īlso If you need more than 20 routes on your GPS, or you prefer to work with tracks in general, or you have non Garmin GPS, you can use WinGDB to create a track from the route. Also additional info like xbk (no bicycles allowed) or bkrt (bicycle route) give further info about the type of ways. Here you can see the names of the streets/routes and as suffix the type of road. To see on what kind of streets a route is calculated, double click the route and click on the “directions” tab. Additional Tipps: Type of Way, way attributes You can use WinGDB to make tracks out of routes (see below). If this is not the case either transfer it, or use tracks instead of routes. If there are more routes old routes may be overwritten, if the route name does not differ in the first 12 characters, the same will happen.Īttention: Recalculation of a route on GPS can only work if the same map that is used to generate the route in Mapsource, also is activated on the GPS itself. Note that most units have a maximum of 20 routes that they can save, and the filename for a route is maximum 12 or 14 characters long. Therefore contrary to sending cards, you have to connect the GPS via USB to your computer. Attention Mapsource will also send routes to an external cardreader, but you can’t reopen them. Now click on Transfer à Send to device and send the route to the GPS.If you don’t mind some detours you could both times use “faster distance”. step of calculating the route with “shorter route” and “prefer highways” so that the route is rather straight. This way route recalculation will be more or less the same as in Mapsource. Now I usually set Mapsource Preferences to “faster route” and leave the slider in the middle. Back in Mapsource, Right click on the route and recalculate it.Please note as of WinGDB Version 3.50 Option 5 is found under Route Conversions with number 15. You can either save the output or reopen it in a new Mapsource window ( on Output Mapsource is checked), which is what we do here now. To start WinGDB click on "Convert". I usually set 5km for routes that go through cities, or up to 9km for cycle routes alongside national/international cycle routes like the “Donauradwanderweg”. The lower the distance the closer your GPS will stick to the route calculated. ![]() You can set in preferences the average distance between via points that should be used. Open Wingdb (0.43 or later - download it here: ), open the saved route and use option "5.Go to File à Save as and save the route as gdb file (the default filetype).Plan your route in Mapsource, To do that click on the route tool (the tool in the middle):Īnd click at each point you want to go to.Now click on close, and in the Routing window click on Apply. Therefore I would advise simply dividing these values by a factor (i.e. You can play around changing to other speeds, but the more you change here, the greater will be the difference on your GPS in terms of how it recalculates the routes as you can’t set these speeds on your GPS itself. Changing Interstate Highways or major Highways speed value does not matter. Note that I only divided the lower three values by two. If you wan’t to have more accurate time information go to advanced and set the following speeds: In case you plan a cycle route and want to avoid difficult tracks and trails check “Toll Roads” in the “Try to Avoid” panel. I usually set Mapsource/Basecamp to use Car/Motorcycle – Shorter Distance – Prefer Highways slider to the right (this is found under tools à Preferences à Routing) (Deutsch) Allgemeiner – Support auf Deutsch (members only).Quick Introduction ID-Editor, Josm and Potlach2.Send maps with Basecamp (Mapinstall) or Mapsource.Install Garmin Basecamp (and maybe Mapsource).How to install the Openmtbmaps – Windows.Send Maps to GPS with Mkgmap (Cross-Platform).Screenshots from the very first openmtbmap in 2009.Garmin Transalpin Review and Interesting News.Premium DEM Relief Shading Maps for Garmin GPS devices.Premium Windows/Linux – Velomap Downloads.Premium Gmapsupp.img – directly for Garmin GPS units.Windows/Linux – OpenMtbMap Map Download. ![]()
0 Comments
Leave a Reply. |